ISCRA dielectrics, a company operating for thirty years in the dosing field, official distributor of Fisnar Europe, guides you in the articulated world of dispensing valves, describing how they work and interact with the dispensed material
by Mascia Mazzarolo
Selecting a valve that will apply a lubricant, adhesive, or coating calls for at least three considerations: knowing how valves work, fluid characteristics, and how the material will be applied. Although this sounds simple, it’s complicated by at least seven different basic pneumatic valves, fluid characteristics that vary, and applications that call for sprays, dots, or thick lines. A little study, however, can simplify the selection.
How the valves work
Pneumatic valves are frequently selected for dispensing jobs because they cycle fast and work reliably.
These valves are powered by timed air pulses that open seals or gates which let a material flow.
Return springs close the seals. Faster cycling calls for a 4way valve, one that needs an initial air pulse to open the seal and another pulse to snap the seal shut after the timed interval. These pneumatic units are available as spray valves, needle valves, diaphragm valves, spool valves, poppet valves, pinch tube valves, and positive displacement valves, which can have adjustable or fixed outputs.
Spray, needle and diaphragm valves
Spray valves work best with low-viscosity material, typically less than 1,000 centipoise (cps). For comparison, water has a viscosity of 1 cps while mustard paste, about 200,000. To ensure a proper selection from this category, consider the angle of spray permitted by the valve and the control module. This latter device ensures atomization takes place prior to material flow and remains on momentarily after flow ceases. This prevents clogging, common with conformal coating products. Needle valves are ideal for single, micro shot deposits for many fluids, providing the valve is suitably configured to handle the fluid. These valves are often adjustable when rated for the high pressure that lets them handle high viscosity unfilled material. Needle valves are also suitable for applying beads of low-to-medium viscosities because they can be opened for any period. Needle valves are also available with a replaceable cartridge seal mounted between the wet-chamber and moving parts. This allows setting a maintenance schedule based on valve cycles. These are not recommended for abrasive materials, which can clog. Diaphragm valves are chosen for adjustable high-cycle dispensing of many low-to-medium viscosity fluids including glues, solvents, and corrosive agents. They are light-weight and easily maintained.
Spool and poppet valves
Spool valves are suitable for high-viscosity pastes, treacle, and gels. These valves operate at high material feed pressures necessary to move high-viscosity fluids. They include a suck-back or snuff-back feature. Spool valves also work well applying beads. With proper automated control, a spool valve can, for example, seamlessly deposit a beaded path of fluid on a gasket. Poppet valves are similar to spool valves with features such as suck-back, but work with low-to-mid-high viscosities. Poppets can apply a smaller shot size than a spool valve.
Positive-displacement and pinch-tube valves
Pinch-tube valves work well dispensing aggressive solvent base fluids because they have disposable wetted parts. These designs work with moderate precision and repeatability within the confines of a pinch-tube design. The pinch-tube valve is often used for two-part, meter-and-mixed applications where the material will cure. The low-cost tubes are disposed at prescribed intervals. Positive-displacement valves are used in tasks that require highly accurate micro deposits. The choice, either a pneumatic or electrically controlled auger or screw valve, is determined by viscosity and shot size. Pneumatic valves can positively displace lower viscosities than auger valves. Pneumatic positive-displacement valves are also less expensive than electrically controlled augers.
Even material makes the difference: low, medium and high-viscosity
To get a better idea of where each valve works best, let’s examine several industrial fluids and their applications. For instance, consider a thin material (100 cps) that cures fast, such as cyanoacrylates. The fluid will likely need purging, or a valve feature that parks the tip in a material that prevents clogging between dispense cycles. The valve design must separate air-actuated moving parts from the wetted parts. Watery or low-viscosity fluids require a valve that allows flow at low pressure, often gravity feed. Such materials call for either pinch-tube, needle, or diaphragm-operated valves. Medium to high-viscosity fluids have the consistency of cream. Pressurized reservoirs that feed such materials to a valve can require degassing and agitation. Spool or poppet valves that include a suck-back or snuff-back feature are appropriate for such materials. Medium-viscosity fluids can also be dispensed with pneumatically operated needle valves. High-viscosity (500,000 cps) and corrosive materials with abrasive fillers will need heavy duty pneumatic valves with corrosive and abrasive-resistant seals. The material content calls for more frequent maintenance intervals than less abrasive materials.
Thick fluids are dispensed from their cartridges and pails
Thick fluids, such as gels or silicones, are usually dispensed from their container, often 0.1-gal. cartridges, or 1 to 5-gal. pails. Thick fluid in pails is extruded to the valve by pneumatic pumps using a follower-plate correctly sized to the diameter of the container.
It mechanically forces material through a high-pressure braided hose to the valve.
A word of caution: Pneumatically pressurized cartridges can show an effect called tunnelling in which only the material in the centre is pushed out, especially when the package is not designed for automated dispensing. ISCRA dielectrics always advise the customer to ask the supplier about the packaging suitability to ensure a good final output.
The thixotropic nature of some fluids After viscosity, consider the thixotropic nature of some fluids
These are difficult to pour but agitate them and they take on a creamy consistency and move easily against themselves. Ketchup is an example. Fluids with the consistency of a thick syrup are subject to the same requirements as gels but often come in small cans that have not been degassed.
Therefore, consider how the material is to be fed to the valve so the fluid is air-free. Paste-like fluids have still higher viscosities and are dispensed directly from their packaged container. The material often comes degassed but confirm that with its manufacturer. Pneumatic valves appropriate for pastes are spool, poppet, and high-pressure-needle valves. Electrically operated auger or screw valves are also recommended when it’s necessary to deposit small amounts of high-viscosity fluids.
Author: Mascia Mazzarolo, Marketing & Sales Department, ISCRA dielectrics